Quantum Audio Network Router FC420 User Guide

FC420 Fibre Channel Bridge  
Quick Reference Guide  
This Quick Reference Guide  
Step 1: Prepare for Installation  
explains how to install one  
FC420 Fibre Channel bridge in  
an ATL M1500 library, or up to  
three FC420 bridges in an  
ATL M2500 library.  
1
Make sure your system meets the following requirements:  
Point-to-point/fabric or arbitrated public or private loop topology  
For fabric configurations, a Quantum-approved Fibre Channel switch  
Quantum-approved network management software package  
If you are unfamiliar with any of  
the information or procedures in  
this document, the Quantum  
Help Desk is ready to assist you  
24 hours a day, 7 days a week.  
To reach the Help Desk, call the  
number for your area listed in  
the Quantum ATL M-Series  
®
®
Windows NT 4.0 SP6 or later, Windows 2000 SP2 or later, Solaris  
8 and 9, or other Quantum-approved operating system  
Note: For a complete list of Quantum-approved networking hardware,  
software, and operating systems, contact the Quantum Help Desk or an  
authorized Quantum sales representative.  
User’s Guide (PN 6423002).  
Note: The FC420 Fibre Channel bridge can only be used in LVD-  
configured libraries.  
This document and others  
related to the ATL M-Series  
libraries are provided in PDF  
format on the Quantum  
ATL M-Series Library User’s  
Documentation CD  
Make sure you have the tools recommended for this procedure:  
®
#1 PHILLIPS screwdriver  
Flat blade screwdriver  
(PN 6423013).  
2
Verify the contents of the FC420 Bridge Upgrade Kit, referring to the  
Quantum FC420 Upgrade Kit Contents List (PN 6473023).  
Note: Adobe Acrobat Reader  
is required to view and print  
PDF documents. To  
download a free copy of  
Adobe Acrobat Reader, go to  
Caution: The small form-factor pluggable (SFP) connector on the  
FC420 bridge is removable; however, the SFP connector should only be  
removed by authorized repair personnel. Removal of the SFP connector  
may void the warranty.  
3
Take precautions to prevent electrostatic discharge (ESD). These  
precautions include:  
Wearing a properly grounded antistatic wrist strap  
Wearing other antistatic apparel (smock, footwear, etc.)  
Handling library components with care and keeping the FC420 bridge in  
its antistatic packaging until you are ready to install it  
Caution: Failure to take adequate antistatic precautions may result in  
damage to the FC420 bridge or other library components.  
 
FC420 Fibre Channel Bridge Quick Reference Guide  
8
9
Insert the FC420 bridge into the expansion slot and press it down gently until it is seated securely.  
Secure the FC420 bridge to the electronics module using the two mounting screws you removed in step 5.  
10 Repeat steps 5 through 9 to install any additional FC420 bridges.  
11 Reattach the hold-down clamp to secure the FC420 bridge in the slot.  
12 Slide the electronics module back into the library chassis until it is fully seated.  
13 Secure the electronics module to the chassis. To secure:  
The primary electronics module, use a flat blade screwdriver to tighten the two thumbscrews.  
The secondary electronics module, reinstall the six screws you removed in step 4.  
Step 3: Cabling the FC420 Bridge(s)  
Each FC420 bridge has 2 SCSI ports and 1 Fibre Channel port. Follow these guidelines to establish SCSI and Fibre  
cabling:  
If the library is equipped with DLT8000 tape drives, the FC420 bridge can accommodate up to four drives per SCSI  
port.  
If the library is equipped with SDLT 220, SDLT 320, or HP LTO Gen 1 drives, the FC420 bridge can accommodate up  
to two drives per SCSI port when the bridge is set for 2 Gb data transfers, or one drive per SCSI port when the bridge  
is set for 1 Gb data transfers.  
If the library is equipped with HP LTO Gen 2 or SDLT 600 drives, the FC420 bridge can accommodate one drive per  
SCSI port when the bridge is set for 2 Gb data transfers.  
Note: HP LTO Gen 2 and SDLT 600 drives cannot be used when the bridge is set for 1 Gb data transfers.  
To maximize data throughput, reduce the number of tape drives per FC420 SCSI port.  
The open connector on each drive must be terminated.  
Because of the physical characteristics of the SCSI cable connectors, attach a SCSI cable from the upper SCSI port  
on the SCSI controller in the primary electronics module to a SCSI connector on drive 1 first, then attach a SCSI  
cable from SCSI port 0 on the FC420 bridge (the left VHDC1 connector) to the lower SCSI port on the library SCSI  
controller.  
To ensure access to the library robotics, all Fibre Channel cables from the library should connect to a switch or  
similar device serving the storage area network (SAN).  
For complete cabling instructions, refer to the FC420 Fibre Channel Bridge Option User’s Guide (PN 6473031).  
3
 
 
FC420 Fibre Channel Bridge Quick Reference Guide  
Step 4: Configure FC420 Bridge Firmware  
A command-line interface (CLI) is provided to assist with FC420 bridge configuration, maintenance, and system  
diagnostics. Specifically, you can use the CLI to:  
Configure the Ethernet, Fibre Channel, and SCSI ports  
Create device maps  
Obtain FC420 bridge status information  
Log FC420 bridge events  
Report SCSI and Fibre Channel device information  
For complete configuration instructions, refer to the FC420 Fibre Channel Bridge Option User’s Guide (PN 6473031).  
Note: If your library is equipped with an MC300 Prism Management Card, you can change the configuration of  
the FC420 bridge, you can do so using the Prism Management Console Web pages (see the MC300 Prism  
Management Card User’s Guide, PN 6311631).  
Copyright 2003 by Quantum Corporation. All rights reserved.  
Your right to copy this document is limited by copyright law. Making copies or adaptations without prior written authorization of Quantum  
Corporation is prohibited by law and constitutes a punishible violation of law.  
Quantum Corporation provides this publication “as is” without warranty of any kind, either express or implied, including, but not limited to, the  
implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication from time to time without  
notice.  
PN 6473033-03, Ver. 3, Rel. 0  
6207947-02sN 1  
 

Radio Shack Battery Charger 23 322 User Guide
RCA Camcorder F32715 User Guide
RCA MP3 Player TC1702 User Guide
Remington Trimmer RM115ST User Guide
Royal Sovereign Laminator ES 410 User Guide
Samson Computer Monitor AURO3 User Guide
Sanyo DVR DSR 300 User Guide
Sanyo Flat Panel Television CE32DFN2 B User Guide
Sanyo Microwave Oven EM S5597B User Guide
Sennheiser Headphones 502399 User Guide